Search found 72 matches

by evilm3666
Wed May 31, 2017 8:24 am
Forum: Bosch
Topic: 413 turbo questions
Replies: 26
Views: 17963

Brian is correct. Just turn the o2 off when tuning then turn it back on when finished.
by evilm3666
Wed May 31, 2017 8:20 am
Forum: Bosch
Topic: bmw m50b25 turbo 413 dme
Replies: 2
Views: 3475

That's pretty good numbers.
by evilm3666
Tue May 16, 2017 8:14 am
Forum: Bosch
Topic: help please! :( dme 413 turbo
Replies: 4
Views: 4262

Not real sure what you are asking,but I will give it a shot. The top of the ignition advance and fuel tables are m.s. of load. You need a scanner to view load or you can use the active trace with the moates.net ostrich to see what cell you are referencing at that moment.
by evilm3666
Thu May 11, 2017 8:17 am
Forum: Bosch
Topic: m52tub24 xdf
Replies: 1
Views: 2920

Check out the BMW section on the romraider forums.
by evilm3666
Sun May 07, 2017 1:43 pm
Forum: Bosch
Topic: 413 turbo questions
Replies: 26
Views: 17963

AFR @ idle and cruise 14.7
If you are running a tune calibrated for the same maf you are using
Then you should not adjust the maf curve. This will change the load reading. Just adjust all the fuel tables until the AFR is correct.
Adjusting the fuel tables does not change the load.
by evilm3666
Mon Apr 03, 2017 7:33 am
Forum: Bosch
Topic: stock chip for 413/m52
Replies: 9
Views: 10272

Its in the download section.
by evilm3666
Mon Apr 03, 2017 7:30 am
Forum: Bosch
Topic: New 506 xdf/bin in 413 silver, runs but cel 1281
Replies: 3
Views: 3404

There is no issue with the checksum. You will get the 1281 cel if you don't save the bin you are editing before for you burn the chip or upload to the ostrisch. The checksum is not corrected until you save the bin.
by evilm3666
Thu Mar 23, 2017 1:13 pm
Forum: Bosch
Topic: Car wont start with chip 506 413 bmw e36
Replies: 3
Views: 3432

It's not the checksum. It will only trip a CEL . You need to confirm your burn. Take the tune from the chip that runs, read it out and burn it to another chip and see if it starts.
by evilm3666
Fri Mar 03, 2017 11:50 am
Forum: Bosch
Topic: NEW BMW 506 xdf
Replies: 8
Views: 6721

files sent
by evilm3666
Thu Feb 09, 2017 4:46 am
Forum: Bosch
Topic: 413 turbo questions
Replies: 26
Views: 17963

PM me your email
by evilm3666
Wed Feb 08, 2017 4:34 pm
Forum: Bosch
Topic: 413 turbo questions
Replies: 26
Views: 17963

I don`t think they posted it up to the downloads yet.
by evilm3666
Wed Feb 08, 2017 8:06 am
Forum: Bosch
Topic: 413 turbo questions
Replies: 26
Views: 17963

HI Brian Shor. Looked at the turbo tune you sent me and it has all the load references re scaled by the injector constant.
by evilm3666
Tue Feb 07, 2017 5:28 am
Forum: Bosch
Topic: 413 turbo questions
Replies: 26
Views: 17963

If you start out with a turbo bin everything will be rescaled in the background. You will have to input a maf curve and then shift the whole curve to get the load to read correctly. Then just adjust the fuel tables. The fuel tables will not change your load reading. So if your maf curve and load sca...
by evilm3666
Tue Feb 07, 2017 5:18 am
Forum: Bosch
Topic: 413 turbo questions
Replies: 26
Views: 17963

So you have to make sure all load axis for all the constants and any reference tables. You don't need to rescale the load axis for any of the fuel or ignition tables. Plus you can't go past 12.75m.s. of load so you can't rescale them to like 15m.s. . You could change the axis to get more resolution ...
by evilm3666
Mon Feb 06, 2017 10:00 am
Forum: Bosch
Topic: 413 turbo questions
Replies: 26
Views: 17963

Sorry but you are way off. You need to rescale every table, constant that references load by the injector constant. There are like 30 some. If this is not done you will have a lot of problems. This was posted elsewhere. NickG 9-30-2008, 07:40 PM With a naturally aspirated motor and stock calibration...
by evilm3666
Wed Feb 01, 2017 7:01 am
Forum: Bosch
Topic: 413 red label -623 lambda and charcoal canister disable
Replies: 2
Views: 3139

The toggle for the closed loop correction was made public in 2012. But I was not aware it was changing the evap also. Have you changed the other bits to see what they may do. Also I have spent lots off time on the dyno and the street with no issues having the closed loop correction turned off. PM me...
by evilm3666
Fri Jan 27, 2017 12:10 pm
Forum: Bosch
Topic: NEW BMW 506 xdf
Replies: 8
Views: 6721

Looks like it has not been posted to the download section yet.
by evilm3666
Sat Jan 14, 2017 5:14 am
Forum: Bosch
Topic: NEW BMW 506 xdf
Replies: 8
Views: 6721

Files sent.
by evilm3666
Thu Dec 29, 2016 10:12 am
Forum: Bosch
Topic: NEW BMW 506 xdf
Replies: 8
Views: 6721

NEW BMW 506 xdf

I just sent a updated xdf for the BMW 506 chip number 965 This has many updates from the one that is in the download section. It has the launch control/2 step rev limiter, corrected the scalars for the speed limiter, found the table for the IAC (idle air control), found the tables for Closed loop ( ...
by evilm3666
Thu Dec 29, 2016 9:44 am
Forum: Bosch
Topic: Launch control for 506 bin. WORKING
Replies: 13
Views: 16872

tason423 files sent.
by evilm3666
Mon Dec 26, 2016 6:40 am
Forum: Bosch
Topic: 413 ECU - ADX FILE ... PLZ
Replies: 3
Views: 3568

This can be downloaded on the downloads section of tunerpro.net
by evilm3666
Sun Jun 12, 2016 4:44 pm
Forum: Bosch
Topic: Lambda adaptation - 413 Red Label
Replies: 1
Views: 2927

xdf sent.
by evilm3666
Fri Mar 18, 2016 8:18 am
Forum: Bosch
Topic: 700hp E36 M3 413 Red lable XDF
Replies: 7
Views: 7363

All you have to do is change the address tables to work with your software version. What software number are you using?
by evilm3666
Sat Feb 13, 2016 9:58 am
Forum: Bosch
Topic: 413 Silver label .bin and .xdf and EWS2
Replies: 8
Views: 9089

by evilm3666
Sat Dec 26, 2015 6:11 am
Forum: Bosch
Topic: race tune for BMW S50 413 silver label
Replies: 5
Views: 5847

Please make sure the bin file chip number matches the xdf you are using. You can check the chip number in Tunerpro by going under tables and opening DME chip number table and see what the last three digits are and make sure it matches the xdf. For tuning VANOS you want to use tables "Vanos, MAX Load...
by evilm3666
Wed Dec 23, 2015 4:47 am
Forum: Bosch
Topic: race tune for BMW S50 413 silver label
Replies: 5
Views: 5847

pm me your email address and I can send you a more complete xdf.
by evilm3666
Mon Dec 21, 2015 4:41 am
Forum: Bosch
Topic: race tune for BMW S50 413 silver label
Replies: 5
Views: 5847

All of that is possible. Start doing research.
by evilm3666
Thu Apr 16, 2015 4:20 am
Forum: Bosch
Topic: Launch control for 506 bin. WORKING
Replies: 13
Views: 16872

Please pm me you email address if you have not yet.
by evilm3666
Fri Mar 06, 2015 5:45 am
Forum: Bosch
Topic: 413 silver label on m52b28 + maf + table question
Replies: 3
Views: 5505

Check this out. It would be a better option than a 803. The HPX is a much more robust maf for a blow through set up. This tune is based off a 506 tune, which you can use in your 413 silver DME. http://www.bimmerforums.com/forum/showthread.php?2162088-tuner-pro-bin-for-turbo-s52-gt35r-60lb-injectors-...
by evilm3666
Thu Mar 05, 2015 11:42 am
Forum: Bosch
Topic: 413 silver label on m52b28 + maf + table question
Replies: 3
Views: 5505

1-Yes you can start with the 413 stock map 2- The 540 maf is not going to be big enough for a turbo set up, you will max it out. The 803 or HPX would be much better. Make sure you download the correct xdf for bin with the 540 maf then just change the axis from 16x16 to 1x256. That is the correct sca...
by evilm3666
Mon Mar 02, 2015 4:59 am
Forum: Bosch
Topic: 413 Silver label .bin and .xdf and EWS2
Replies: 8
Views: 9089

Should be posted on the downloads page in a few days or so.
by evilm3666
Mon Mar 02, 2015 4:50 am
Forum: Bosch
Topic: 413 Silver label .bin and .xdf and EWS2
Replies: 8
Views: 9089

pm me your email address and I will send you it.
by evilm3666
Sun Feb 01, 2015 11:35 am
Forum: Bosch
Topic: 413 506 rpm scaling/high rpm xdf
Replies: 1
Views: 3942

It is not that difficult, but you will lose some resolution. Pm me your email address
by evilm3666
Sun Oct 19, 2014 3:33 pm
Forum: Bosch
Topic: Launch control
Replies: 3
Views: 5450

The same DME can be used with the 413 red label, 413 silver label or the 506 bin.
by evilm3666
Sun Oct 19, 2014 5:13 am
Forum: Bosch
Topic: Launch control
Replies: 3
Views: 5450

email sent with 506 files
by evilm3666
Sun Oct 19, 2014 5:06 am
Forum: Bosch
Topic: Launch control for 506 bin. WORKING
Replies: 13
Views: 16872

No the launch control only works on the 413 silver label and the 506. The launch control is really just a fuel cut rev limiter that is based on vehicle wheel speed. The 413 red label does not have this type of rev limiter. You can just use the 506 bin file in your currant DME.
by evilm3666
Tue Aug 12, 2014 8:33 am
Forum: Buell
Topic: Harley ecm reading and reflashing
Replies: 11
Views: 15279

I have a number of bikes i can use, but i have no idea how to read the data from the ecm. I have used the power vision and the supertuner as far as tuning goes. I am sure it can be read/ with the 1850 data line.
by evilm3666
Tue Jul 15, 2014 9:02 am
Forum: Buell
Topic: Harley ecm reading and reflashing
Replies: 11
Views: 15279

Harley ecm reading and reflashing

Does anyone have any info on pulling the bin file for any harley ecms? Or maybe a xdf?
by evilm3666
Tue Jul 01, 2014 3:09 am
Forum: Bosch
Topic: stock chip for 413/m52
Replies: 9
Views: 10272

Pm me your Email and I will send you a bin file and a xdf.
by evilm3666
Tue Apr 01, 2014 6:52 am
Forum: Bosch
Topic: BMW ECU 413 REV Limiter
Replies: 52
Views: 73163

I am not sure if you can do this with a 402/403. I have never looked at bin file for those. I emailed you the files for the 506 on the 30th.
by evilm3666
Tue Apr 01, 2014 6:27 am
Forum: Bosch
Topic: BMW ECU 413 REV Limiter
Replies: 52
Views: 73163

That just looks like the speed based revlimiter that has six break points. The 413 silver and 506 dme have that in the code all you have to do is change a few things. Pm me your email and I can send you the files.
by evilm3666
Wed Feb 19, 2014 2:55 pm
Forum: Bosch
Topic: 413 red label the ecu don`t gey values from WOT fuel tables
Replies: 8
Views: 9001

If you are using the bin I sent you there should be no type of limiter to keep it from referencing the wot tables. Are you sure that there is no tps wiring issue?
phob pm me you email. I have something you can try.
by evilm3666
Thu Feb 13, 2014 7:23 am
Forum: Bosch
Topic: 413 red label the ecu don`t gey values from WOT fuel tables
Replies: 8
Views: 9001

I use a snap-on mt2500 scanner. Or I have data running in to my dyno for logging. Do you have any check engine codes? Also did you download the files or did I email you them?
by evilm3666
Thu Feb 13, 2014 6:21 am
Forum: Bosch
Topic: 413 red label the ecu don`t gey values from WOT fuel tables
Replies: 8
Views: 9001

Make sure you are using the correct bin for the xdf. I would reload the stock bin and start with that to make sure the bin file is not corrupt. Make sure are pressing "initialize emulation hardware" button and then upload the bin to the ostrich and than press the "enable emulation" button. I make ch...
by evilm3666
Tue Feb 04, 2014 11:07 am
Forum: Bosch
Topic: Launch control for 506 bin. WORKING
Replies: 13
Views: 16872

The 506 xdf file is finished. It has working launch control, the load and rpm axis are auto correcting so if you open up a bin that had any of the rpm break points changed it will auto correct in Tunerpro for correct break point viewing. I also corrected any tables that are load based like the VANOS...
by evilm3666
Thu Jan 16, 2014 7:03 am
Forum: Bosch
Topic: Launch control for 506 bin. WORKING
Replies: 13
Views: 16872

Launch control for 506 bin. WORKING

I got launch control / 2 step rev limiter working for the 506 bin. It will be easy to change the rpm settings and to enable or disable in Tunerpro. I just need to finish up a 506 xdf file for N/A cars. It will be for the 506 chip #965. I will send out the xdf and a stock bin modified with the launch...
by evilm3666
Sun Dec 29, 2013 7:44 am
Forum: Bosch
Topic: 413 506 dme
Replies: 2
Views: 4690

It sounds like the bin file does not match the xdf you are using. There is more than one bin for the 413 red label ecu. Each bin has the data at slightly different locations. So you need to make sure that the xdf matches the chip you are using. You can view the chip number through the xdf, there is ...
by evilm3666
Mon Nov 18, 2013 12:11 pm
Forum: Bosch
Topic: BMW ECU 413 REV Limiter
Replies: 52
Views: 73163

can you switch to the 623 chip? I can send you the xdf for that with the o2 sensor disable. or you can send me the bin for your chip and I can see what I can do.
by evilm3666
Wed Oct 09, 2013 8:58 am
Forum: Bosch
Topic: Table and MAF questions
Replies: 10
Views: 21798

the maf is in KG/hr and voltage and it just needs to be rescaled to a signal curve to view it correctly. The updated xdf has it rescaled and converted to kg/hr, but the voltage break points are not done.
by evilm3666
Thu Aug 29, 2013 8:59 am
Forum: Bosch
Topic: BMW 413 xdf files
Replies: 19
Views: 28281

For a 7000rpm you should be able to put in 7000. Make sure you are starting with the correct chip#. I have a updated xdf for 413 silver ews II ecu chip#715
PM me your email