Buell datalogging

Discuss Buell tuning topics here. Request definitions, discuss parameters, etc.
Post Reply
aaronja77
Posts: 3
Joined: Tue Jan 17, 2012 2:25 am

Buell datalogging

Post by aaronja77 » Tue Jan 17, 2012 2:36 am

I am running a NGK Powerdex WB controller on my 09 Buell. This has a 0v-5v analogue output that I am running through a toggle switch to pin 1 and pin 33 on my ecm. This is so I can switch between datalogging rear and front.

I am logging the rear and it is coming through as AFR2. At idle it is showing a value of 87. What does this value represent as I am looking for a value in the 9-16 AFR range? Does there need to be a conversion equation done in the ADX value for AFR2?

Thanks
Aaron
2009 Buell XB12ss

User avatar
EagleMark
Posts: 424
Joined: Mon Mar 22, 2010 11:11 am

Post by EagleMark » Tue Jan 17, 2012 5:50 pm

I'm not sure if this is correct for Buell but it is the equation used for WBO2 0 to 5 volt in other adx files.

X * 0.039063 + 10.000000
1990 Chevy Suburban
1994 Buick RoadMaSSter Estate Wagon LT1.
1972 IH 1210 Isky Cammed Balenced 345 TBI

GearHead-EFI.com EFI Conversions and Chip Tuners!

aaronja77
Posts: 3
Joined: Tue Jan 17, 2012 2:25 am

Post by aaronja77 » Tue Jan 17, 2012 6:50 pm

Hi

Would the x 0.039063 be the conversion to volts?

I know that the conversion from volts to AFR is V x 1.4 + 9. This gives the unit a range of 0-5v = 9-16AFR.

Cheers
2009 Buell XB12ss

User avatar
EagleMark
Posts: 424
Joined: Mon Mar 22, 2010 11:11 am

Post by EagleMark » Tue Jan 17, 2012 7:31 pm

I don't know? There's a math wiz at link in my sig named greg78scam that helps us understand some of these conversions.

This was in the equation of the Advanced $OD adx written by 93V8S10 for WBO2 AFR by using the 0 to 5 volt pintle EGR signal through ECM. kinda what your doing in your adx. It also had a note:
0v= 10.0 AFR, 5v= 20.0 AFR
Input on pin B16
Linear EGR Pintle Position
1990 Chevy Suburban
1994 Buick RoadMaSSter Estate Wagon LT1.
1972 IH 1210 Isky Cammed Balenced 345 TBI

GearHead-EFI.com EFI Conversions and Chip Tuners!

Xoptimizedrsx
Posts: 5
Joined: Sat Oct 02, 2010 9:25 am

Post by Xoptimizedrsx » Wed May 16, 2012 3:13 pm

attached is a small screen shot of one of our Access database sheets I compile things from. this is a basic sheet but it shows a pattern you may want as info. We have every ecm and every data byte so anything can be added to the adx and XDF if needed... note page one data is omitted in the Read write for a safety measure.

Image

aaronja77
Posts: 3
Joined: Tue Jan 17, 2012 2:25 am

Post by aaronja77 » Wed May 23, 2012 12:11 am

Cheers Mike.

I can see how to export the datalog but is there a way to export, amend the log and then import?

When datalogging, I am getting blips in the readings which I want to filter out as these will distort my history table and subsequent fuel map changes.
2009 Buell XB12ss

Post Reply